Schedule Now!

 

 

The writer is making several great pointers on the subject of Tools You Need to Install a New Bathtub overall in the article following next.

Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old tub with a new one is additionally a moderately hard project. If the old tub is conveniently easily accessible, the task can move easily; if you have to open up a wall surface to eliminate the old tub and also position the new tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the task as well as are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to consider using one before you start. Chances are you might need a professional plumber to make tube connections.
This write-up will certainly assist you install a brand-new bath tub in your shower room if you have already acquired a brand-new tub and also don't need to transform the plan of your previous supply of water pipes.
Your devices as well as material checklist ought to comprise the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Preparing for the Installation

To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final placement.

 

 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water supply. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome as a result of the restricted access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.

 

 

Mounting the Tub

Using both wooden boards under its feet, position the tub in the called for setting. The wooden boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by checking the level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit all-time low of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water as well as examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bath tub and additionally inspect the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, fix the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the tub should wait up until the bathtub has been made use of a minimum of when as this will resolve it into its final placement.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making sure that the washing machines are in location between the tap and also the sink. Secure the faucet in place with the maker given backnut. When the faucet is securely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type needs to be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Tub

In the location where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bath and the tiling, causing difficulties with wetness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the tiles making use of waterproof or water-proof glue as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I am just very enthusiastic about Installing A Bathtub and I am praying you enjoyed the post. Enjoyed reading our blog entry? Please share it. Let another person discover it. Many thanks for taking the time to read it.

Request Appointment